2011 Demolition Derby
General Rules
- Safety Page 1
- Car Building Rules
- Frame and Body Rules
- Interior Rules
- Suspension Rules
- Tire Rules
- Bumper Rules
- Repair Rules
1. Official’s decision is final.
2. This is a family sport. Please try and remember that. No profanity allowed on the cars. No one under the influence of drugs or alcohol will be allowed to participate. Classless behavior will not be tolerated.
3. Fuel. No alcohol or methanol, unless pump gas ethanol, allowed. Electric fuel pumps allowed. Fuel injection allowed however, all high-pressure fuel hose must be covered. Low-pressure fuel hose under pressure must have a minimum of two clamps per fitting. High-pressure hose and fittings recommended.
4. Tire rule. We do not want flats. No bigger than 16” rims, no split rims, no studded tires on driven wheels. Implement tread, forklift type, foam filled, solid, and double tires allowed. Valve stem protection allowed. No rim reinforcements. No liquid filled tires allowed. No spikes, paddles, or other material to be welded inside or to the rim. No wheel weights allowed. Rim screws are allowed.
5. Driving. You must make aggressive contact with another live car in less than one minute. If you do not make aggressive enough hits, we will let you know. No intentional driver door hits. Depending on the severity of the hit, we may simply warn you, or we may break your stick. If you use your driver’s door to block another car, do not expect that car to be disqualified for the driver’s door hit. Official’s decision final.
6. During competition stay in the car. Keep your helmet on. Keep your hands and arms inside the car.
7. During competition, no driver, pitmen, or spectators shall approach the officials. Classless behavior will not be tolerated. Official’s decision is final.
8. If you are black flagged (for example a door hit), you finish in that spot, not last, and receive that place trophy and winnings, if any.
9. Cars may be disqualified at any time. We will re-inspect after the derby is over. IF a car is found to be illegal, it will be disqualified and finish last.
10. Protest fee. We allow protests. $200.00 cash is required to protest. It must be presented to the officials with the specific complaint. The officials, and only the officials, will then check the complaint. If it is illegal, and it is severe enough to change the outcome of the event, the protested car will be disqualified.
Back to top
Safety Page 1
These rules are REQUIRED and must be met or you will not run
1. Overall condition must be safe. This applies to used cars as well as fresh cars. IF the officials deem the car unsafe to run, it will not run. The official’s decision is final.
2. SFI-1 or better, Certified Fire jacket required. SFI-1 or better, pants recommended. Long pants are required. Eye protection, Neck Brace and gloves highly recommended. Shoes are required.
3. Minimum of D.O.T. rated helmet required. Full-face helmets recommended.
4. Seat belts are required, must be functional, and fastened to the floor or seat bracket and must be at all times. Official’s decision is final, must be safe.
5. Car must be fully stripped of all flammable material. Factory seats and factory dash are allowed. All glass, chrome, door handles, and any unsafe items must be removed from the inside and outside of the cars. All plastic, stainless and pot metal trim, fiberglass, and rubber must be removed from the outside of the car. Car floor, trunks, and inside of doors must be swept of glass, debris, and must be clean. Factory floor drain plugs must be removed.
6. Factory fuel tank(s) must be removed. Unused factory fuel lines must be blown free of gas. Removing unused fuel lines recommended. Factory fuel tank may not be re-used.
7. A steel seat support (seat bar) is required from the inside of the driver door(s) across to the passenger door(s), must be behind the seat, and must be no farther back than 6” from back of driver’s seat. Cars with two doors may have a seat bar at the rear of the doors at the door jam. A second seat support bar is also allowed forward of this rear support bar, placed just behind the driver seat. This seat bar must be made of steel, 2” x 2” x ¼” square, 2 ½” x ¼” round minimum, 6” x ½” square or round maximum. Steel plates are required on the ends of this seat bar, 6” x 6” x ¼” minimum, 12” x 12” x ½” maximum. These steel plates must be welded well to the seat bar (official’s decision is final, must be safe). The steel plates may be bolted to the car, however welding is highly recommended. IF the factory dash is removed, a support (dash bar) similar to the seat support is required. If you use a dash bar, it may be connected to the seat support bar with similar material. These “door” bars may be against inner door skin. These “door” bars may not extend past the dash or seat supports more than 6”. 2 down bars on the driver side are allowed in the door opening (front down bar must be a minimum 6” behind interior front door seam), these down bars must extend straight down from the door bar to the frame. 1 down bar on the passenger side is allowed in the door opening, but to floor tin only. Driver door bar, and driver down bar, is highly recommended.
8. Driver door must be welded shut for safety. Welding the outer driver door seams completely is highly recommended. Welding the inner driver door seams allowed. Outer driver door skin reinforcement is allowed and highly recommended. This reinforcement must be steel sheet metal only, may be no thicker than 1/4”, and must conform to the factory bodylines. This reinforcement may not extend in front of the front door seam more than 6”, and may not extend past the rear door seam more than 6”. This sheet metal may be bolted, however welding is highly recommended. No grader blades, pipes, “C” channel, or other material allowed on the outside of the driver door other than sheet metal. Reinforcement on the inside of the driver door with pipe, down bar and other material is allowed.
9. Halo bars and or rollover bars are allowed. The addition of “posts” on hardtop sedans (connecting top of doors to roof) is also allowed. Roll over cages may run on the exterior of the roof, and must be welded to the seat support and or dash support (if used). Connecting these roll over cages to the roof is required. The rear roll over bar, behind the seat, must be vertical (not angled up and back). This rear roll over bar may extend down through the floor tin and to the top of the frame or sub-frame. This rear roll over bar may be welded to the top of the frame or sub-frame (top of frame only).
10. A minimum of two steel straps or bars must be located in windshield area. These may be bolted or welded and must only attach to sheet metal only (2” round or 2” x 2” square maximum). These straps or bars may not make contact with the roll over or halo bars. These straps or bars are required to prevent the hood from entering the passenger compartment (official’s decision is final, must be safe). 11. Metal allowed, in two spots, from the dash support bar forward to the dash and or firewall sheet metal only. This metal may not make contact with the windshield bars or straps. 4” wide by ¼” thick maximum allowed.
12. Battery must be re-located inside of passenger compartment. The battery must be in a solid container and must be securely fastened and covered (official’s decision is final, must be safe).
13. No steel gas “cans” or plastic gas “jugs” allowed. A steel boat tank is allowed, however, any metal tank deemed safe by the officials is acceptable. Metal tanks do not need to be covered. Any plastic or urethane “fuel cell” must be in a solid metal container and must be covered with metal. The fuel tank must be securely fastened inside the passenger compartment. Official’s decision is final, must be safe.
Compact class only, may leave the factory gas tank in factory position only if it is in front of the rear axle.
14. Hoods must have a minimum of two 12” holes for fire control.
15. Cars must have some type of working brakes. Drive shaft brakes are allowed (official’s decision is final, must be safe).
16. Engine oil and transmission coolers are allowed. IF air coolers (fans) are used, a shield must be located between the cooler and the driver. High-pressure (hydraulic type) lines and fittings are recommended. No gas hose is allowed. It must be compatible with transmission oil. If low pressure rated oil hose is used, minimum of two hose clamps per fitting. Non high-pressure oil hose must be covered. Engine cooler hose and fittings must be high pressure.
17. Low-pressure rated fuel hose in the passenger compartment, from electric fuel pump to fire wall, must be covered.
18. No wheel weights or balance weights allowed on wheel rims. Valve stem protection is allowed.
19. Radiator coolant over flow tubes must point straight down. Any large holes in the firewall must be covered with non-flammable material to prevent competitor from being sprayed by hot oil, or water.
20. NO distributor protectors or valve cover protectors allowed.
21. $100.00 CASH PROTEST FEE for any feature driver who wants to protest a car who has placed ahead of him/her. The protester must express reasonable complaint of the car he/she is protesting. The money will go to whoever wins the protest. Officials will not cut a car apart but may cut an inspection hole in the protested area if necessary. If any violations of the rules are found, the car will be disqualified and forfeit all prize money.
OFFICIALS WILL RESOLVE ANY AND ALL DISAGREEMENTS. ALL DECISIONS BY THE OFFICIALS WILL BE FINAL. CARS WILL BE RE-INSPECTED BEFORE ANY PRIZE MONEY IS HANDED OUT.
CarBuilding Rules
These rules will be used for the 2011 season and supersede all other previous years Nebraska Unified Rules. You must first pass all Required Nebraska Unified Rules for Safety (listed on separate sheets of paper).
Demolition Derby
2011 Car Building Rules
Note: These are car building and preparation rules only. Any additional restrictions and rules such as no profanity, size of numbers on doors, registration times, age of participants, releases, local track rules, (such as no Imperials allowed, or 81’ and newer only cars) alcohol consumption, etc., are the duty of the promoter, and should be included on a separate sheet of paper.
These rules are for the full size, passenger cars only class. No hearses, ambulances, limos, 4 wheel drive, vans, minivans, or any vehicle considered a "truck" or "SUV" allowed. “Cross-Over” type vehicles are up to the promoter and or officials for that specific event.
If it is not allowed in the following rules, then do not do it.
1. Official's decision is final.
2. No Imperial sub-frames under non-Imperial cars. ‘67 – ‘73 Imperial sub-frames under ‘67 – ‘73 Imperials only. ‘66 and older Imperial frames under ‘66 and older Imperials only. 2003 and up Fords must remain stock, (body, Frame, Engine saddle, and front suspension must remain stock) Watts link Rear end maybe changed out.
3. Frames must remain stock. No re-welding factory frame seams. No filling factory holes in frame. No frame plating inside or out. No re-painting frames with paint or under coating. No "grease and dirt tricks". No welding on frame anywhere, other than what is allowed in the following rules.
4. Re-welding of factory frame seams (both top side and bottom side) from the front of the "A" frames forward is allowed. 1/2" wide weld bead maximum. The re-welding (12” total length, ½” wide bead maximum, per frame rail) of factory frame seams from the “A” frames rearward is allowed. This rule is to allow the welding of frame seams that were not welded correctly at the factory. Only a total of 12” allowed. This may be 5” on top, 7” on the bottom, etc, (builder’s choice) for a total of 12”, per frame rail.
5. Cutting and or pre-notching the rear frame rails are allowed, but must not re-weld any part of it. No adding of extra, non-factory body mounts to the frame and body allowed.
6. Engines and transmissions may be interchanged from make and model of car. Engine must be in stock location (NO sliding the motor back). Engine and transmission mounts may be fabricated and welded as long as these mounts do not strategically reinforce the frame, “A” frame mounts, or shock towers. No engine mounts, cradles, braces, cables, or chains may extend more than 4" in front of, or 4" behind the engine block. Maximum length of frame angle or frame plate is 4”. Maximum size allowed is 2” x 2” x ¼”. Angle or plate must extend upward from top of frame. Rear Engine mounts may only be Maximum 2” x 3/8” flat iron attached to the top of the main frame rails, or top of the angle or frame plate to the back of the engine. NO tying front to rear engine mounts together. NO welding to the vertical frame surfaces. "K frames” in cars may be welded to the main frame rails. A maximum of 1/2" diameter rod, as filler, allowed. No plates between the frame rails and “K frames” as filler, allowed. This filler rod and or weld must not extend more than 4” in front of, or 4” behind, the engine block. Fabricated transmission mounts are allowed. Transmission mount brackets, welded or bolted at the frame rails, are allowed. The front edge of these brackets must start at least 5” behind the firewall body mount bolts. On Ford cars, these mounts must be 5” from the rear of the “crush box”. Maximum length of these brackets is 12”. Maximum size angle allowed is 3” x 3” x 3/8”. Two ½” bolts allowed from transmission cross member up threw the floor tin. Distributor protectors and valve cover protectors are NOT allowed. Transmission cradles, braces or struts (to protect the transmission) are NOT allowed.
7. Body mount bolts may be replaced with up to 1" diameter bolts. Body bushing maybe removed; body may sit flat on the frame. Longer body mount bolts that enter the interior of the car are allowed. Maximum 5” washers or plates on the topside of the trunk pans and floor pans are allowed. Sub-frame cars may have washers or plates up to 2" larger than factory body mount hole (for example: if the hole is 4", the use of an 8" washer or plate is allowed). These washers or plates may not be fully welded to the trunk pans or floor pans. Bolts must be cut flush with top of nuts. Washers or plates, under or in the frame, must be in the stock location of make, model and year, but may be up to 2" larger than the frame hole diameter. The addition of two body mount bolts, (one bolt per frame rail) through the body isolators in the rear seat area of GM sedans allowed. The addition of two body mount bolts through the floor sheet metal, down to the shock absorber towers, below the rear speaker deck, in Mopar cars allowed. The addition of two body mount bolts (one bolt per frame rail) through the frame, near the top of the "humps" in 71' - 76' GM station wagons allowed. These bolts are allowed to be put in the spot where GM made a provision for a body mount, but only installed this body mount in a few wagons. Now all wagons are allowed to have this mount. 74” – 78” Mopars may but a sub bolt in the provisionary body mount hole in sub frame rail where the transmission mount and frame meet. Bolt cannot go through the bottom of the frame.
8. Radiator support mount bushings may be removed completely. The radiator support may contact the frame but must not be welded to it. Two “radiator mount” bolts are allowed to attach the radiator mount to the frame. The two “radiator mount” bolts may be up to 1" diameter. These two bolts may be welded to the frame. These two bolts may extend straight down threw to the bottom side of the frame. These two bolts may be placed on the outward side, or inward side, of the frame rails. No angling back to “A” frames to form a “kicker”. These two bolts may extend up next to the radiator support, through to the top of the hood, and be used as two hood hold down bolts. These two bolts may be welded to the radiator support. These two bolts may be welded to the frame if they do not go down through the frame. Thicker (taller than factory) spacers are allowed between the radiator support and the frame. No bolts allowed in front of radiator. #9 wire, in four locations, (2 loops or 4 strands each) may be used from the radiator support (core support) down to front bumper. A bushing or nut (1” inside diameter maximum) allowed to be welded to the top of the bumper to attach the #9 wire.
9. All trailer hitches, tow bars, and other material used for towing, must be removed completely.
10. Bodies must remain stock. No re-welding factory seams inside engine compartment. No re-welding factory body seams inside passenger compartment, trunk compartment, or seams under body. No re-welding seams under hood or seams under trunk lid. No adding metal to body other than driver door.
11. Hoods must be open for inspection. Hoods must remain in the stock location and position. Bending down, or bending up, excess hood in front of radiator support allowed. Hoods must have a minimum of two 12” holes (round or square) for fire control. Holes cut in hood for fire control, or exhaust, may be bolted (not welded) back together with up to twenty 3/8" bolts (1" outside diameter washers maximum). Hoods must be either chained or bolted shut. You may use only one method to hold the hood. No angle iron with bolts may be used. No wire may be used to fasten hood.
If bolted shut: A minimum of four bolts, 5/8" diameter, must be used. These minimum four bolts must be used with washers or plates with a minimum of 4” diameter. A maximum of eight bolts, not to exceed 1" diameter is allowed. The factory hood hinges do not count as a hood hold down. Only the front two bolts may go down through the hood to the frame. The other six bolts, if used, must be sheet metal to sheet metal only. Washers or plates for the topside of the hood may not exceed 5" square and 3/8" thick. The hood washers or plates may be welded to the top of the hood. 5" square washers or plates may also be welded to the inner fenders at the corners (fender to radiator support and fender to the firewall or cowl), just below the hood. Bolts may then be bolted or welded to these washers or plates to hold the hood.
If chained shut: A minimum of four spots of 1/4" chain must be used. These minimum four chains must be used with washers or plates with a minimum of 4” diameter. A maximum of up to eight spots of 3/8" chain may be used. The use of 5" square washers or plates is allowed as above.
12. Radiators must be in the stock location and may use factory type mounts. Ratchet straps, wire, and chain may be used to hold in radiator. Aluminum radiators may be used. Electric fans may be used. Air conditioner condensers may be welded directly to the radiator support, and may use filler rod (1/2” diameter maximum) or plates to do so. Up to four spots may be used. Maximum size allowed is 4” tall by 1/8” thick. These filler plates may be bolted or welded to the radiator support and to the air conditioner condenser. No “protectors” for the radiator allowed.
13. Fenders may be cut for a larger wheel well opening. Fenders may be bolted or welded back together. Only one method may be used. Up to twelve 3/8" bolts (1" diameter washers maximum) per wheel well opening allowed. Full welding allowed, however, only one fold of the radius allowed. No extra steel allowed. Excess front fender in front of radiator support may be cut, folded over, and bolted (not welded) back together. Four 3/8" bolts (1" washers) allowed per fender.
14. Doors must be chained, wired, bolted, or welded (exterior seams only) shut. Driver door must be welded shut (official’s decision is final, must be safe). Chain must be a minimum of 1/4", wire must be a minimum of two loops, bolts must be a minimum of 3/8", and weld must be 4" on a minimum of two spots per door. No chain, wire, or bolts allowed to go to or around frame. 4" wide by 3/16" strap maximum allowed to weld over door seams. Other exterior body seams may be welded. 3" wide by 3/16" strap maximum allowed.
15. Trunk lids and station wagon tail gates may be chained, wired, bolted, or welded shut (the same as the doors). Any two methods allowed fastening the trunk lid or tailgate. No method may go to, or around the frame or rear bumper. 60% of the trunk must be in factory position. 40% of the rear of the trunk lid may be "tucked" down inside the trunk compartment. Trunk lid may not be welded to the trunk floor pan. Two bolts (maximum 1" diameter) are allowed in the trunk from the bottom of the trunk pan up through the top of the trunk lid. These two bolts are allowed to go down through the frame, but may not be welded to the frame. The use of 5" washers or plates is allowed the same as the hood. These two bolts must be cut flush with the top of the nuts. Pre-forming or pre-bending the body sheet metal is allowed. It may be cut to shape it, but may not be re-welded or bolted back together (except for the front edge of the front fenders, wheel well radius, and hood holes).
16. “NO Wedging” of sedans allowed. Station wagon tail gates may be lowered, then chained, wired, bolted, or welded shut.
17. Tops of doors, and areas that had moving windows, may be pinched together and welded. Weld bead only, no plates or other material allowed. Inspectors must be able to see down into the doors and body.
1. No re-welding of interior body seams. The re-welding of the doorpost or pillar, to the floor sheet metal, allowed on both the driver side and passenger side.
2. The use of fabricated parts such as steering columns, fuel pedals, brake pedals, transmission shifters, seat brackets, battery boxes, fuel tanks, and coolers allowed. Transmission and engine oil coolers are allowed. Two batteries are allowed. Distributor protectors are valve cover protectors not allowed.
3. Seat, battery, fuel tank, and cooler brackets must be welded to, or bolted to, the floor sheet metal. No chain, wire, or rubber type straps allowed to fasten these items. The seat, battery, fuel tank, and coolers must be secure (official’s decision is final, must be safe). No bracket may be attached to, or come in contact with, the seat bar, dash bar, or door bars. Steering column brackets and seat brackets may come in contact with, and be attached to, these bars. No bracket may extend in front of the dash bar (other than steering column bracket, and brackets that go forward to the firewall or dash). No bracket may extend past the rear of the rear seat bar. Brackets in the front seat area must be welded to, or bolted to, floor sheet metal only. Brackets in the back seat area must be welded to, or bolted to, the floor sheet metal only. Bolts in the back seat area may not go through, or around, the frame or sub-frame. Brackets in the back seat area must not be attached to, or come in contact with, the seat bar or door bars. Brackets for the front seat area, and brackets for the back seat area, must be completely separate. The official's decision is final.
4. Roll bars or “halo” bars, above the rear seat bar, must extend vertically, not angle back.
5. One post or pillar is allowed in the rear window area. 2” x 2” square, or 2” round maximum size allowed. This post or pillar must mount (bolted or welded) to the back edge of the roof and extend down to the front edge of the trunk lid. One 5” x 5” x ¼” maximum size plate allowed at the top, and one 5” x 5” x ¼” plate allowed at the bottom. This post or pillar, with plates, must be mounted to sheet metal only. This post may not make contact with any bracket for roof sign.
6. Remove or loosely fasten rear "decking" in station wagons. It may be bolted, wired, or chained, but not tightly. No method may go to, or around, frame or sub-frame. Must be sheet metal to sheet metal only. Two bolts (1” diameter maximum) may be used in station wagons. These two bolts may go from the bottom of the frame, up through the decking, and up to the top of the roof. These two bolts, with washers or plates, are similar to trunk lids on sedans. "Decking" may not be welded. A 12" (round or square) inspection hole in "decking" or lower floor sheet metal is required.
7. Number nine wire; #9 wire is allowed in all year cars. #9 wire is allowed in fresh cars. Two spots per window allowed. Each spot may be up to 2 loops (four single strands). This #9 wire is allowed only from the roof, straight down, to the flat area of the floor. Washers (1” inside diameter maximum) allowed to be welded to the roof. The #9 wire is allowed to wrap around the frame rails. The #9 wire may also be attached to the floor area, and to the body mount washers or plates. No #9 wire may be attached to the front firewall body mount bolts or plates. The #9 wire may only be attached to the flat area of the floor. #9 wire must be vertical. No crossing of loops. Official’s decision is final.
1. No leaf springs under non-leaf cars allowed. No solid suspension. Suspension must be working and have a minimum of 2" travel. No reinforcing of steering or suspension components other than what is allowed in these rules.
2. The interchange of front spindles, rotors, "A" frames, and steering gear boxes allowed. The parts must not be reinforced or altered and must be considered OEM car, not truck or SUV. Only a minimum of fabrication is allowed to do this. The "A" frame mounts, if needed, may not strengthen the frame, or be stronger than what is considered stock.
3. Rear axle assemblies may be interchanged, but may not be full floater type. Must not have more than five wheel studs per axle shaft. “Hybrid” type housing assemblies are allowed. Rear axle housing braces are allowed. Mounts may be fabricated. Mounts may be a maximum length of 12”.
4. No more than 9 leaf springs per side, no more than 3/8" thick leaves. The leaves must stagger down to bottom spring with a minimum of 1" stagger. The leaf directly under the main may not extend longer, or past, the main leaf eyebolt. No double wrapping of the main leaf. No leaf may be as long as the main leaf. No leaf springs on top of, or above, the main leaf allowed. 6 leaf spring clamps allowed per leaf spring pack, 12 total per car. Maximum size of clamps is 2" wide by 4" long by 1/4" thick.
5. Factory rear control arms on coil spring cars may be lengthened or shortened. Only a minimum of reinforcing is allowed. “Boxing” of rear control arms, allowed. Double coil springs are allowed, (one coil spring turned inside a second coil spring). Coil springs may be wired, welded, or cabled in on top or bottom. Only one place is allowed to hold coil spring in (top or bottom, builder’s choice). Air shock lines must be cut.
6. Front and rear factory leaf spring brackets, on Mopar cars, may be welded to the floor brackets, and or sub-frame brackets. Leaf spring cars may move rear of leaf springs under frame. Fabricated rear shackles are allowed. Front leaf spring brackets, on leaf spring cars, may be reinforced, but must not strategically reinforce the frame or rear sub-frame.
7. No chain, wire, cable, or similar methods allowed attaching rear axle housing to frame or body, other than what is allowed below.
8. Shocks are allowed and must have 2” minimum travel. One strand (not loop) of chain (no wire or cable) 3/8” size maximum allowed to replace the shock. This strand of chain must be mounted at the same factory location, both top and bottom, as the factory shock. Or you can loop chain (no wire or cable) 3/8” size maximum around frame and rear end, “NO WELDING” to frame. You may use only one form, shock and loop around frame, or one strand of chain, not both (builder’s choice). The chain links must not be welded. The chain must flex.
9. Wire (four loops maximum) or cable (one loop of 3/8") from driver side frame rail, across to the passenger side frame rail, is allowed. If used, it must be located above and behind the rear axle housing. This wire or cable may go through or around the frame rails. No welding of brackets to the frame.
1. We do not want flats.
2. No balance or wheel weights allowed on any rim.
3. No bigger than 16" rims, no split rims, no studded tires on driven wheels. No rim reinforcements. No spikes, paddles, or other material to be welded inside or to the rim. No liquid filled tires allowed. Rim screws allowed. Implement tread, forklift type, foam filled, urethane, solid, and double tires are allowed. Valve stem protection is allowed. Any ply allowed.
1. Any car bumper allowed on any car. Bumpers may be chained, bolted, or welded on. Bumpers may be cut. Bumpers may be welded to the brackets. Brackets may be welded to the frame. Bumpers may be welded to the frame. Brackets may be cut. Use only factory brackets, NO extra steel or other material allowed as a bumper bracket. You may use either the factory brackets that came with the bumper, or you may use the factory brackets that came with the car, not both (builder’s choice). Bumpers may have seams welded, no extra steel or material allowed in, or on, bumper. Bumper chrome may be welded to inner bumper support. Bumpers may be mounted upside down. Rear car bumpers allowed on the front. Front car bumpers allowed on the rear. Rear bumper brackets may only be used on the rear of the car. Front bumper brackets may only be used on the front of the car. No bracket may extend rearward more than 14” from the back of front bumper. This is measured at the factory mount surface. Brackets may be bent to conform to the frame rails. Brackets may not be cut and butt-welded together to strengthen the frame. All brackets must make contact with the bumper. Mopar cars 1973 and older (Y-framer), may only “plate” (factory brackets) only ONE side of the “Y”. Top side or bottom side, not both (builder’s choice).
2. Imperials, ‘73 and older, may not have 5 MPH bumpers mounted on them unless that body style came with them from the factory. Rear bumpers, and rear bumper brackets, are not allowed on the front of ‘73 and older Imperials. Must use only front brackets and front bumpers on ‘73 and older Imperials. Only single layer bumper chrome allowed.
3. Two straps 3” x ¼” x 10” long from rear bumper to trunk lid allowed. #9 wire allowed from front of radiator support, down to the top of front bumper. Bumper chrome may be welded to the body sheet metal on non-cushion (non-5-mph) bumpers where it makes contact. Bumper chrome may not be welded to the body sheet metal on Cushion (5-mph) bumpers where it makes contact. Bumpers must be smooth at the edges. Bottom of rear bumper must be a minimum height of 14”.
Repair of Used Cars, Rust Repair:
1. Repairing, straightening, fixing, and rebuilding cars that are damaged is allowed. Repairing, fixing, rebuilding damaged cars to better or stronger than it was original and fresh is NOT allowed.
2. NO multiple layers of sheet metal on or in body allowed (other than driver door). Repair to cuts and tears to sheet metal is allowed, but must remove damaged area before you replace or patch it with the same gauge sheet metal. Patches must be same thickness as factory material for that car. Official's decision is final.
3. Welding cracks in frames of used cars is allowed. No plating on or in the frame is allowed. If the frame metal is torn, it may be welded with no filler or extra metal allowed. Weld bead only. If the frame is damaged, the damaged area may be cut out and replaced with the same thickness material. Do not overlap metal, butt weld only. Do not grind weld down flush when finished. Do not buff. We need to see the repair. Making the damaged area stronger or better than original is NOT allowed. Do not paint over or undercoat repairs. Official's decision is FINAL on all repairs.
4. Patching or repair of rust is the same as repair to tears in sheet metal and repair of damage to frame. Patching or repair of rust to stronger or better than original is NOT allowed.
5. Cross-hatch type welding on frames for repair is not allowed. Single bead weld, for cracks, is allowed on frames. Official’s decision is final.
6. “Number 9” wire is allowed as repair on all year cars.
7. Steel Plates as repair to damaged frames on used cars are allowed. NO steel plates allowed on fresh cars. Up to three spots per frame rail is allowed (builder’s choice). These plates may be up to 6” wide. These plates may be a maximum thickness of 1/8”. These plates may be as tall as required for that particular section of frame rail. These plates must have an edge extend above and or below the frame rail (minimum ½” exposed) to allow verification of plate thickness. These plates may be butt-welded together (builder’s choice). These plates, as repair, may not overlap. These plates are allowed as repair only on used cars. These must be legitimate repairs. No plates allowed on fresh cars. These steel plates must have a minimum of a 1” hole in the center to allow verification of a legitimate repair.
These rules will be used for the 2011 season
